bush craft knives

here is a few pictures of some of my favourite bushcraft knives , the green knife is a frost's mora clipper with a carbon steel blade it cost me £10 from ray mears bushcraft site its easy to sharpen and stays sharp ,the blade is just inder 4inches on the mora with an overall length of 8 and a half inches the sheath is hard plastic with a belt clip on it the handle of the mora is very comfortable and a little bit soft the other knives i,m not sure what specific make they are as they have no makers markings on them but they are good quality knives ,the big bowie knife i like to use to make bows the big one has a wood handle and a 8 and a half inch blade and the overall length is 13 and a half inches and the small one is good for all round jobs its blade length is 5 inches and overall it is 9 and a half inches with what beleive to be a carbon steel blade

AIR RIFLES gamo realtree hunter

air rifles are fully capable of taking many small game humanely with ease, one great air rifle is the gamo realtree hunter , my version has had the barrel shortened to have a supressor fitted plus a new ox main spring fitted inside , as well as a sling and swivels , it also has a AGS 3-9x50 mildot telescopic sight ,the stock on this rifle is "synthetic" plastic but its very very strong with a really good realtree camo pattern ,the rifle is full power or near enough about 11.5 ft lbs , but with a really easy to cock break barrel my version is .22 they also come in .177 i have hunted squirrel ,rabbit, pheasant ,pigeon, with this rifle dispatching all with ease this gun is really light weight easy to carry for extended periods

survival air rifle

a normal air rifle or firearm (if legal in your country ) can be modified to be smaller and more compact with features such as a screw in hollow stock which can be filled with survival items or a folding stock with a compartment for survival items the measurement for a legal uk air rifle over 6ft lbs is 60cm overall length with a barrel of 30 cm minimum i will add to this post as i continue with the project ,the first thing i wil do is cut off the stock i .ll mark the stock with tape so the guns overall length is over 60 cm i,ll also make sure the barrel is over 30 cm then cut off the stock, now the stock has been removed you need to round it off then dril a hole which will be your pivot for your folding stock to make the stock you,ll need 2 peices of 5mm aluminium my measurements were 1 inch by 8 & a half inch long but you could make it the same size as what you already cut off you also need a small shoulder peice which could be the end of the old stock cut off take a look at the pics ,drill a hole through both bits of ali about half inch from the end to make a kind of hing then put a bolt through as in pics now you need to srew on the butt piece just a few holes then screw on now the easiest way to lock the stock in place when open is to drill a hole and put a pin through attached to the stock by a piece of paracord so as not to lose it

simple snaring

a simple snare can be made using brass wire and a wooden peg make a noose then attach to a peg , then drive into the ground so the snare is over a game trail , for rabbit make the noose a fist wide, and 3 fingers high from the ground

snaring

snares are a great thing to keep in survival kits as they are very small and light . in the picture is a spring snare covering a hole under a fence . to make a snare all you need is some brass wire ,then make a small loop in it then pass your other end through the hole to make a noose, then attach to a peg driven into the ground or to a notched peg of a spring snare

pheasant trapping

pheasants are one of my favourite animals to trap ,heres some great traps for this , the one in the pic is a version of the arapuca bird trap but with a mesh cage , you need 4 sticks on one carve a notch (holding stick) then cut a stick with a 2 slanted point tofit into the notch to hold up the holding stick then 2 more sticks (trigger sticks) to hold back the holding stick

figure 4 trap mechanism

the figure 4 trap mechanism is an easy trap to make needing no string or cordage just a knife . you need 3 sticks first you need to carve square notches into 2 of them so they fit into each other to make a cross shape then you need to carve the vertical one into a 1 sided point and the cross piece (bait stick) need a slanted notch cut in then you third peice (holding stick) need a 2 sided point cut in and at one end to fit into the bait stick notch then a notch cut out to fit the top of the first stick

johnjayrambo11111

hello its me johnjayrambo11111 (malc) from youtube and i,ll use this blog page to post pictures and more info about survival stuff